Dosbox conf file location12/26/2023 ![]() (Initial configuration is optimized for FullHD Monitors, however this guide has you covered up to 4K resolution.) (Comments marked with "#" are additional information and must not be added into the Config-file.) (this step requires you to have started and closed DOSBox at least once!)Ĭhange all values you find there to the following ones: bat"-file to open the DOSBox Configuration-Textfile. ![]() "C:\Games\DOSBox\") and double click on the "DOSBox 0.74 Options. Make sure you are in the correct section before you change values.Īnything in DOSBox that has a " #" at the start of a row will be ignored by DOSBox and is considered a comment, this is handy to leave yourself notes which configuration values to use for which game.Įnter your DOSBox-directory (i.e. Short explanation, each DOSBox-Section has a title in brackets, i.e. This guide will be based on that "Games"-folder, if you don't create it you will have to adjust this guide for yourself accordingly. When the installation is finished, start up DOSBox for it to create all necessary files for this guide, then close it again.Īdditionally, I recommend to manually create a new folder inside the "DOSBox"-folder named "Games". Simply download the Installer-Version and install DOSBox to your desired directory by following the on-screen instructions, i.e. The most up-to-date Version (as of 26.July.2019) is "0.74-3", though this guide will work identically for all "0.74" versions. The latest DOSBox Version can be downloaded for free from following site: 9 Roland MT-32 (and other Roland devices).7 YouTube & Game Resolution & OBS Settings.In my case, I did not do this because I am using Dosbox-SVN, and there is no documentation where to put the base config and how to name it, so I skipped this step. The result should be a new entry “DOS” in your systems list, with each game nicely listed and ready to launch using its corresponding config file.Ī way to improve this would be having a single base config file and just add the autoexec section to each game-specific config. Turn off “Scan Recursively” (this is to exclude the game folders themselves, you only want to scan the.Open the scan menu and select “Manual scan”.But if you set up a manual scan, it will magically work. conf files does not work as expected, Retroarch ignores them. This is tricky because for some reason, automatically scanning the. Now the most important step: Getting the games to show up and launch in Retroarch. ![]() This will be different for every game, but you can usually figure it out by looking at the files in the game folder. Then, edit the config files and for every game, add an autoexec section at the bottom that looks like this: It does not have to exactly match the game folder’s name. The filename will be used as the game’s title in the Retroarch menu. When you have the config file, create a copy of it for every game you want to launch in your /roms/dos folder: conf file in C:\Users\user\AppData\Local\DOSBox on Windows or ~/.dosbox/ on Linux You can also download and run the standalone version of Dosbox.conf file will be created in the /saves/ folder (if you cannot find your saves folder, the path is shown in RetroArch under Settings > Directory > Savefile) At the Dos command prompt, type config -wcd. In RetroArch, go to Main Menu, Load Core, DOSBox.Next, you need to create a Dosbox base config file. If you’re on Windows, you need to change your paths accordingly ( C:\roms\dos).įirst, copy each game to its own folder like this: ![]() Note: I am using Linux path names for this example ( /roms/dos). As information seems to be scarce, I wanted to share a way of getting Dosbox games to work with Retroarch, and most importantly, getting your games to scan and show up in the games menu. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |